Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.
Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.
Blog Article
Do not ignore the forklift at the office. If the operation is bad, there will be serious mishaps in mins, and there are numerous crashes including forklifts.
Instance 1: The forklift freight obstructed the vehicle driver's sight, and the individual in front might not be located, causing a rolling crash.
Case 2: In order to preserve the balance of the forklift when lifting heavy goods, the workers utilized their body weight as the weight, which practically triggered casualties.
Situation 3: The width of the forklift freight goes beyond the allowable width of the route and holds on the roadside shelf, which almost creates an accident.
Situation 4: Forklift is speeding and surrender throughout a turn.
Instance 5: The forklift vehicle driver did not discover the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the employees unlawfully, the forklift motorist does not use the seat belt, the forklift lifter falls and the chauffeur is squashed when the forklift surrender.
Situation 7: The forklift chauffeur did not wear a seat belt and dropped from the lorry when it rolled over and was squashed.
Forklift procedure need to pay attention to these matters ：.
Beginning.
1. Prior to starting, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and afterwards start.
2. For vehicles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale have to be safe before starting.
3. When the forklift begins with a load, the driver ought to initially validate that the lots is stable and reliable.
4. The begin must be sluggish and constant.
Driving.
1. When driving, the elevation between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the mast must be tilted in reverse. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job site or while driving, beware that there will be no barriers overhead. When the tons is taking a trip, the fork needs to not be increased expensive, which will certainly influence the security of the forklift. .
3. After dumping, the fork must be reduced to the typical driving position before driving. .
4. When turning, if there are pedestrians or lorries close by, the driving signal needs to be released initially. High-speed sharp turns are forbidden. High-speed sharp turns will certainly create the automobile to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely prohibited to shut off the flame and slide, and it is restricted to brake unexpectedly while driving with loads unless there are unique circumstances.
6. When the forklift is running, it has to comply with the web traffic rules in the manufacturing facility and need to maintain a particular security distance from the lorry ahead. .
7. When the forklift is running, the tons must remain in the most affordable setting that does not impede the driving, and the gantry should be correctly tilted back. The tons shall not be increased except when piling or loading. .
8. The elevation of the load should not obstruct the chauffeur's view. In special scenarios, when the thing influences the forward vision, drive at a reduced rate when turning around.
9. It is restricted to activate the ramp, nor to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it has to drive securely at a low speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold products and play a balancing duty. .
12. If troubles are discovered, they will be fixed and reported in a prompt way, and they will never ever operate with diseases or hide them.
packing and discharging.
1. When fork-loading items, the range between both forks must be changed as needed to make the lots of the two forks balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special circumstances, security warning signs should be set up to advise bordering pedestrians. .
3. In the process of loading and dumping products, the forklift has to be stopped with the brake. .
4. The speed of the automobile should be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be noted that the fork pointer ought to not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the load does not move in reverse. The pole can be tilted ahead a little when the load is reduced to permit easy placement of the lots and removal of the forks. .
6. It is restricted to fork products at high speed and ram hard objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to lift personnel to participate in high-altitude procedures to prevent high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to make use of forks to select, transform pallet dump.
Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Draw the emergency brake manage to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique circumstances, such as the driver does not leave the vehicle's line of sight and does not exceed 1 minute).
4. Remove the trick. .
Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look ought to be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of starting, running and braking.
3. Inspect whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leak needs to likewise be inspected and the seals should be changed in time.
Forklift Safety Operation Specifications.
1. You need to inspect before leaving the car;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the freight should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the tendency of " complimentary switching";.
6. Running up and down the incline ought to be slow and consistent, and no turning on the slope is allowed.
7. Do not drive Electric Forklift Truck for Warehouse throughout the gradient. When the slope is greater than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they come across huge or heavy items and go to the vehicle driver's line of vision, they need to take Stand-on Electric Pallet Stacker the reversing workout
.
The "Eight Prohibitions" should be complied with in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not permitted to make use of inertia force to get the goods.
6. It is not permitted to use braking force to expatriation round or easy-to-roll objects.
7. It is not allowed to bring individuals to work with the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Auto parking is not allowed under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the road, the contrary side of the area with the very same size as the obstacle ought to be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844